Annoussamy, M., Richard, G., Recous, S., & Guerif, J. (2000). Change in mechanical properties of wheat straw due to decomposition and moisture. Applied Engineering in Agriculture, 16(6), 657.
ASAE, A. (2000). S319. 3: Method of determining and expressing fineness of feed materials by sieving. ASAE Standards.
ASAE, A. (2003). Moisture measurement forages (pp. 579). St. Joseph,MI, American Society of Agricultural Engineers, p.
Balk, W. (1964). Energy requirements for dehydrating and pelleting coastal bermudagrass. Transactions of the ASAE, 7(3), 349-0351.
Bond, F. C. (1952). The third theory of comminution. Trans. AIME, Min. Eng., 193, 484-494.
Drzymała, Z. (1993). Industrial Briquetting—Fundamentals and Methods Studies in Mechanical Engineering. PWN-Polish Scientific Publishers, Warsaw.
Fellows, P. J. (2009). Food processing technology: principles and practice: Elsevier.
Ghorbani, Z., Masoumi, A., & Hemmat, A. (2010). Specific energy consumption for reducing the size of alfalfa chops using a hammer mill. Biosystems engineering, 105(1), 34-40.
Henderson, S. M., & Perry, R. L. (1976). Agricultural process engineering: AVI Publishing Co. Inc.
Hideno, A., Inoue, H., Tsukahara, K., Fujimoto, S., Minowa, T., Inoue, S., . . . Sawayama, S. (2009). Wet disk milling pretreatment without sulfuric acid for enzymatic hydrolysis of rice straw. Bioresource Technology, 100(10), 2706-2711.
Holtzapple, M., Humphrey, A., & Taylor, J. (1989). Energy requirements for the size reduction of poplar and aspen wood. Biotechnology and Bioengineering, 33(2), 207-210.
Igathinathane, C., Womac, A., Sokhansanj, S., & Narayan, S. (2007). Size reduction of wet and dry biomass by linear knife grid device. ASABE Paper.
Kratky, & Jirout, T. (2014). Energy-Efficient Size Reduction Technology for Wet Fibrous Biomass Treatment in Industrial Biofuel Technologies. Chemical Engineering & Technology, 37(10), 1713-1720. doi:10.1002/ceat.201400243
Lopo, P. (2002). The right grinding solution for you: roll, horizontal or vertical. Feed Management, 53(3), 23-26.
Mani, S., Tabil, L., & Sokhansanj, S. (2003). An overview of compaction of biomass grinds (Vol. 15).
Mani, S., Tabil, L. G., & Sokhansanj, S. (2004). Grinding performance and physical properties of wheat and barley straws, corn stover and switchgrass. Biomass and Bioenergy, 27(4), 339-352.
Padilla-Rivera, A., Barrette, J., Blanchet, P., & Thiffault, E. (2017). Environmental Performance of Eastern Canadian Wood Pellets as Measured Through Life Cycle Assessment. Forests, 8 (9) 352
Rezaeifar, J., Kianmehr.M.H, & Hasanbeygi.S.R. (2008). Investigation Parameters of Pellets from Cattle Manure for Extruder Design
Sitkei, G. (1987). Mechanics of agricultural materials (Vol. 8): Elsevier.
Soleymani, J., Kianmehr.M.H, Hassanbeygi.S, R, & Shariatmadari.S.M. (2018). Design, fabrication and evaluation of a wet cattle manure size reduction machine. (M.sc), University of Tehran College of Abouraihan
Tabil, L. (1996). Pelleting and binding characteristics of alfalfa. Unpublished Ph. D. thesis, Department of Agricultural and Bioresource Engineering, Saskatoon, SK Canada: University of Saskatchewan
Tavares, L. M. (2007). Chapter 1 Breakage of Single Particles: Quasi-Static. In M. G. Agba D. Salman & J. H. Michael (Eds.), Handbook of Powder Technology (Vol. Volume 12, pp. 3-68): Elsevier Science B.V.
Yu, M., Womac, A. R., & Pordesimo, L. O. (2003). Review of biomass size reduction technology. Paper presented at the 2003 ASAE Annual Meeting.
)
